ATLAS Support Center

User Tools

Site Tools

Trace:
itk:testbeam

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
itk:testbeam [2016/09/30 13:53]
asc [Plots without calibration] 		itk:testbeam [2016/09/30 18:05]
asc
Line 1: Line 1:
  
-======  Pixel module test beam ====== +======  Pixel module test beam at SLAC ====== 
-(prepared by S.Chekanov)+(some notes by S.Chekanov)
  
  
 Here are the useful links on test beam in Sep. 2016 at SLAC. The plan is discuses  [[https://twiki.cern.ch/twiki/bin/viewauth/Atlas/ITkPixelTestBeamSLACSep2016|on this wiki at SLAC]]. Here are the useful links on test beam in Sep. 2016 at SLAC. The plan is discuses  [[https://twiki.cern.ch/twiki/bin/viewauth/Atlas/ITkPixelTestBeamSLACSep2016|on this wiki at SLAC]].
  
-What is used: 11 GeV secondary electrons (~100 - 200 per bunch), 5 HZ frequency. Original electron beam is 14 GeV.+What is used: 11 GeV secondary electrons (~10-100  per bunch), 5 HZ frequency. 
 +The beam sport is about 1x1 cm (tunable). 
 + Original electron beam is 14 GeV.
 The setup is described in [[https://confluence.slac.stanford.edu/display/Atlas/TestBeam| Setup at SLAC]]. The setup is described in [[https://confluence.slac.stanford.edu/display/Atlas/TestBeam| Setup at SLAC]].
 To start the run, use: To start the run, use:
Line 27: Line 29:
   * Readout ASIC with 65 nm (vs 130 nm for FE-4IB). This decrease of ASIC leads to smaller sizes.   * Readout ASIC with 65 nm (vs 130 nm for FE-4IB). This decrease of ASIC leads to smaller sizes.
  
 +Here is the setup at the end-station A:
  
-====== How to make calibration ======+This is the  RTI module (uncovered): 
 + 
 +{{:itk:img_20160928_103349.jpg?400|Setup}} 
 + 
 +This is the  RTI module + RD53 prototype (uncovered): 
 + 
 +{{:itk:img_20160928_100735.jpg?400|Setup}} 
 + 
 +Telescope: 
 + 
 +{{:itk:img_20160927_142154.jpg?400|Telescope}} 
 + 
 +Control room upstairs: 
 + 
 +{{:itk:img_20160930_071901.jpg?400|Control room}} 
 + 
 +====== How to calibrate the module ======
  
  
Line 155: Line 174:
  
 <code bash> <code bash>
-/home/tbsclac/pixelrce/rce/moduleconfigs/RTISC2B/config/RTISC2B__cern__158.cfg # from 6.15 AM+/home/tbsclac/pixelrce/rce/moduleconfigs/RTISC2B/config/RTISC2B__cern__225.cfg # from 7.00 AM
 </code> </code>
  
Line 176: Line 195:
  
  
-Both modules from RTI have  shown signs of degradation performance. After about ~6-8h, we start to see problems for the analog  +Both modules from RTI have  shown signs of degradation in performance. After about ~6-8h, we start to see problems for the analog readout. The occupancy for analog channel efficiency for  uncalibrated module goes from 99% to 70% after 6h. The noise increases by a factor 2.   
-channels. The occupancy for uncalibrated module goes from 99% to 70% after 6h. The noise increases by a factor 2.  + 
 +This problem is not related to the active beam, since the red module was not under the beam on Sep 28. 
  
-This problem is not related to the active beam, since the red module was not under the beam in Sep 28.  
  
  
itk/testbeam.txt · Last modified: 2016/10/04 15:11 by asc

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: Public Domain
Public Domain Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki