Differences

This shows you the differences between two versions of the page.

--- phase2:led [2015/07/17 18:43]
asc
+++ phase2:led [2015/09/30 15:07] (current)
asc
@@ Line 1: / Line 1: @@
 ====== TileCal LED tests ======
-Here  is a library with PMT signals with active dividers.
+Here  is a data library with PMT signals with different attenuators.
-The data are collected using R5900 PMT with active dividers and 676 V. Patrick's LED 4 ns width and David's setup
+The dynamic rage is from 1 pC to 2000 pC. The data are collected using R5900 PMT with active dividers and 676 V, and a WLS fibre, Patrick's driver
-All figures are in "figures".
+with 4 ns pulse width and David's LED setup.
-Used 1 neutral density filter 50% (NDF50), and 1 neutral density filter x16 (NDF16)
+The talk that describes this study is [[https://indico.cern.ch/event/441970/contribution/16/attachments/1162896/1675431/LEDResults.pdf| Studies of PMT block signal shapes using passive and active dividers, Tile upgrade week, Sep 30, 2015]]
+Download the signal files from  [[https://atlaswww.hep.anl.gov/asc/phase2/data/]], and then gunzip  it. To make a plot for 1 trace, use
-Download data from  [[https://atlaswww.hep.anl.gov/asc/phase2/data/]]
+<code bash>
-To make a plot for 1 trace, use
+wget --no-check-certificate https://atlaswww.hep.anl.gov/asc/phase2/data/pmt_signals_phase2.tgz -O - | tar -xz;
+cd pmt_signals_phase2/
-<code python>
+python show_trace.py data/D1_traces_full.txt.gz 1 # show 1st trace out of 1000
-python show_trace.py data/D1_traces_full.txt.gz 1
 </code>
-  - D1 NDF16 + 6xNDF50
+We used several 50% (0.3) neutral density filters (NDF50), and 1 neutral density filter x16 (NDF16).
-  - D2 NDF16 + 5xNDF50
+Data files with traces are  in "data/*". There are 1000 traces in each file.
-  - D3 NDF16 + 4xNDF50
+The file names has a letter "D" that indicates attenuation strength for the light.
-  - D4 NDF16 + 3xNDF50
-  - D5 NDF16 + 2xNDF50
+  - D1 NDF16 + 6xNDF50. Reduction of light by 6*2*16. About 0.3 pc -> x1024
-  - D6 NDF16 + 1xNDF50
+  - D2 NDF16 + 5xNDF50 -> x512
-  - D7 NDF16
+  - D3 NDF16 + 4xNDF50 -> x256
-  - D8 3xNDF50
+  - D4 NDF16 + 3xNDF50 -> x128
-  - D9  2xNDF50
+  - D5 NDF16 + 2xNDF50 -> x64
-  - D10 1xNDF50
+  - D6 NDF16 + 1xNDF50 -> x32
-  - D11  - no NDF
+  - D7 NDF16  (light reduction by a factor 16) -> x16
+  - D8 3xNDF50 -> x8
+  - D9  2xNDF50 -> x4
+  - D10 1xNDF50  (light reduction by a factor 2) -> x2
+  - D11  - no NDF. About 2000 pC ->0
+Figures for 1000 traces are in "figures".  Each trace was centralized at time=0. We use a numeric noise suppression for all traces as shown in this image.
+{{:noise.png}}
+Blue lines show traces before the noise removal, and small grey dots after the noise suppression. The green dots show the noise in the LED driver.
+ --- //[[[email protected]|Sergei Chekanov]] 2015/07/17 14:00//

ATLAS Support Center

User Tools

Site Tools

Differences

Page Tools